Word | Definition |
T & G, tongue and groove | A joint made by a tongue (a rib on one edge of a board) that fits into a corresponding groove in the edge of another board to make a tight flush joint. Typically, the subfloor plywood is T & G. |
T bar | Ribbed, "T" shaped bars with a flat metal plate at the bottom that are driven into the earth. Normally used chain link fence poles, and to mark locations of a water meter pit. |
Tab | The exposed portion of strip shingles defined by cutouts. |
Tail beam | A relatively short beam or joist supported in a wall on one end and by a header at the other. |
Take off | The material necessary to complete a job. |
Taping | The process of covering drywall joints with paper tape and joint compound. |
Teco | Metal straps that are nailed and secure the roof rafters and trusses to the top horizontal wall plate. Sometimes called a hurricane clip. |
Tee | A "T" shaped plumbing fitting. |
Tempered | Strengthened. Tempered glass will not shatter nor create shards, but will "pelletize" like an automobile window. Required in tub and shower enclosures and locations, entry door glass and sidelight glass, and in a windows when the window sill is less than 16" to the floor. |
Termite shield | A shield, usually of galvanized metal, placed in or on a foundation wall or around pipes to prevent the passage of termites. |
Termites | Wood eating insects that superficially resemble ants in size and general appearance, and live in colonies. |
Terra cotta | A ceramic material molded into masonry units |
Texture Paint | One which may be manipulated by brush, trowel or other to give various patterns. |
Thermal Shock | The stress built up by sudden and appreciable changes in temperature. |
Thermoplastic Material | Solid material which is softened by increasing temperatures and hardened by decreasing temperatures. |
Thermoply ™ | Exterior laminated sheathing nailed to the exterior side of the exterior walls. Normally ¼ " thick, 4 X 8 or 4 x 10 sheets with an aluminumized surface. |
Thermostat | A device which relegates the temperature of a room or building by switching heating or cooling equipment on or off. |
Three-dimensional shingles | Laminated shingles. Shingles that have added dimensionality because of extra layers or tabs, giving a shake-like appearance. May also be called "architectural shingles". |
Threshold | The bottom metal or wood plate of an exterior door frame. Generally they are adjustable to keep a tight fit with the door slab. |
THW | Moisture and heat resistant thermoplastic conductor. It is flame retardant, moisture and heat resistant and can be used in dry or wet locations. |
Tie-In | In roofing, a term used to describe the joining of a new roof with the old. |
Time and materials contract | A construction contract which specifies a price for different elements of the work such as cost per hour of labor, overhead, profit, etc. A contract which may not have a maximum price, or may state a 'price not to exceed'. |
Tinner | Another name for the heating contractor. |
Tinted Glass | Glass with colorants added to the basic glass batch that give the glass color as well as light and heat-reducing capabilities. The color extends throughout the thickness of the glass. |
Tip up | The downspout extension that directs water (from the home's gutter system) away from the home. They typically swing up when mowing the lawn, etc. |
Title | Evidence (usually in the form of a certificate or deed) of a person's legal right to ownership of a property. |
Title 24 | A federal set of laws that mandates the construction industry to conserve energy. |
TJI or TJ | Manufactured structural building component resembling the letter "I". Used as floor joists and rafters. I-joists include two key parts: flanges and webs. The flange or from of the I joist may be made of laminated veneer lumber or dimensional lumber, usually formed into a 1 ½" width. The web or center of the I-joist is commonly made of plywood or oriented strand board (OSB). Large holes can be cut in the web to accommodate duct work and plumbing waste lines. I-joists are available in lengths up to 60'' long. |
Toenailing | To drive a nail in at a slant. Method used to secure floor joists to the plate. |
Tongue and Groove | A type of flooring where the tongue of one board is joined to the groove of another board |
Top chord | The upper or top member of a truss. |
Top plate | Top horizontal member of a frame wall supporting ceiling joists, rafters, or other members. |
Torching | Applying direct flame to a membrane for the purpose of melting, heating or adhering. |
Transmitter (garage door) | The small, push button device that causes the garage door to open or close. |
Trap | A plumbing fitting that holds water to prevent air, gas, and vermin from backing up into a fixture. |
Tread | The walking surface board in a stairway on which the foot is placed |
Treated lumber | A wood product which has been impregnated with chemical pesticides such as CCA (Chromated Copper Arsenate) to reduce damage from wood rot or insects. Often used for the portions of a structure which are likely to be in contact with soil and water. Wood may also be treated with a fire retardant. |
Trim (plumbing, heating, electrical) | The work that the "mechanical" contractors perform to finish their respective aspects of work, and when the home is nearing completion and occupancy. |
Trim- Interior | The finish materials in a building, such as moldings applied around openings (window trim, door trim) or at the floor and ceiling of rooms (baseboard, cornice, and other moldings). Also, the physical work of installing interior doors and interior woodwork, to include all handrails, guardrails, stair way balustrades, mantles, light boxes, base, door casings, cabinets, countertops, shelves, window sills and aprons, etc. Exterior- The finish materials on the exterior a building, such as moldings applied around openings (window trim, door trim), siding, windows, exterior doors, attic vents, crawl space vents, shutters, etc. Also, the physical work of installing these materials |
Trimmer | The vertical stud that supports a header at a door, window, or other opening. |
Truss | An engineered and manufactured roof support member with "zig-zag" framing members. Does the same job as a rafter but is designed to have a longer span than a rafter. |
Tub trap | Curved, "U" shaped section of a bath tub drain pipe that holds a water seal to prevent sewer gasses from entering the home through tubs water drain. |
Turnkey | A term used when the subcontractor provides all materials (and labor) for a job. |
Turpentine | A term used when the subcontractor provides all materials (and labor) for a job. |
Two-Part Sealant | A product composed of a base and curing agent or accelerator, necessarily packages in two separate containers which are uniformly mixed just prior to use. |
